Hello!
I have just upgraded to new battery with 5200mah instead of the original one with 3200mah.
In the settings in the battery it still shows capacity 2600mah (~80% of total 3200).
How do I change 2600 to higher value so that it mowes longer? Is it possible at all?
Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Verwendet bitte für aktuelle Mäher bzw. falls ihr die Firmware eures Mähers kürzlich aktualisiert habt, den aktuellen Release-Candidate der Robonect-Firmware: https://fw.robonect.de/?latest Diese wird in ein paar Tagen als offizielle Firmware verfügbar sein. (Stand: 03.04.2024)
What to config?
-
- Forum-Nutzer
- Beiträge: 47
- Registriert: So 19. Jul 2020, 11:53
- Wohnort: Nideggen
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.6)
- Robonect Firmware: 1.3
Re: What to config?
Hello bortek,
this subject has been discussed in length here but in German only. From what I understand (I‘m relatively new to Robonect)one needs to fool the original Firmware by telling the mower to act like on a secondary mowing area. Supposedly the FW then allows to enlarge the calculated mowing times (calculated from the nominal battery capacity (resistor!!) and minimum voltage required for safe return). If you switch the feature on, the mower will accept almost any battery capacity and run time regardless of the nominal value.
Does this help?
this subject has been discussed in length here but in German only. From what I understand (I‘m relatively new to Robonect)one needs to fool the original Firmware by telling the mower to act like on a secondary mowing area. Supposedly the FW then allows to enlarge the calculated mowing times (calculated from the nominal battery capacity (resistor!!) and minimum voltage required for safe return). If you switch the feature on, the mower will accept almost any battery capacity and run time regardless of the nominal value.
Does this help?
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 134 Male
Re: What to config?
Only one additional issue: the statistics for mowing and searching times will no longer be shown in Robonect using this feature. Reason: the mowers electronic ist not saving them using this feature, as result of this Robonect can’t show the mowers statistics.
But if you need to use a bigger battery, this will give you more profit then statistics of it.
In a future version of Robonects Firmware new statistics saved by Robonect will solve this.
But if you need to use a bigger battery, this will give you more profit then statistics of it.
In a future version of Robonects Firmware new statistics saved by Robonect will solve this.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- Forum-Nutzer
- Beiträge: 39
- Registriert: Mi 18. Jul 2018, 19:30
- Mäher: Husqvarna Automower 420
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2017
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.0
- wurde gedankt: 1 Mal
Re: What to config?
Thanks for the replies. Yes indeed that's the case. I have tested it by switching the extend mowi g time using mowing time adjustment. Moreover the Timer function for some reason was not working, maybe due to other issue I found, so the mower was mowing 24/7.