No poweron cmd to sonoff/tasmota relay
-
- Forum-Nutzer
- Beiträge: 15
- Registriert: Sa 21. Aug 2021, 18:25
- Mäher: Gardena SILENO City 500
- Robonect Firmware: 1.3
No poweron cmd to sonoff/tasmota relay
Hi,
I have a brand new Robonect module v.9 running Robonect v1.3 and I'm trying to get my sonoff Relay board working for the Passage control but I can't see that Robonect is sending the necessary "power1 on" and "power1 off" commands to the Tasmota sw?
I have tried both the latest tasmota sw as well as an older 8.5.1 version and I can control the Relay locally from the tasmota console without any problems but not from the Robonect Passage web page!
Looking at the tasmota console when pushing the "Passage open" and "Passage close" on the web GUI gives the following:
When "Open Passage" is pressed:
Robonect 1.3 responds: Passage successfully opened at 16:44 clock
Tasmota 9.5.1 console logging:
16:44:49 HTP: Command
16:44:49 SRC: WebCommand from 192.168.1.92
16:44:49 CMD: Group 0, Index 1, Command "BACKLOG", Data "PulseTime1 0"
16:44:49 SRC: Backlog
16:44:49 CMD: Group 0, Index 1, Command "PULSETIME", Data "0"
16:44:49 RSL: RESULT = {"PulseTime1":{"Set":0,"Remaining":0}}
When "Close Passage" is pressed:
Robonect 1.3 responds: Passage successfully closed at 16:48 clock
Tasmota 9.5.1 console logging:
16:48:59 HTP: Command
16:48:59 SRC: WebCommand from 192.168.1.92
16:48:59 CMD: Group 0, Index 1, Command "BACKLOG", Data "PulseTime1 0"
16:48:59 SRC: Backlog
16:48:59 CMD: Group 0, Index 1, Command "PULSETIME", Data "0"
16:48:59 RSL: RESULT = {"PulseTime1":{"Set":0,"Remaining":0}}
As far as I can understand, Robonect is not sending the neccessary "power on" and "power off" command to Tasmota to switch the Relay on and off!
Anyone got any ideas what to do?
Regards Peder
I have a brand new Robonect module v.9 running Robonect v1.3 and I'm trying to get my sonoff Relay board working for the Passage control but I can't see that Robonect is sending the necessary "power1 on" and "power1 off" commands to the Tasmota sw?
I have tried both the latest tasmota sw as well as an older 8.5.1 version and I can control the Relay locally from the tasmota console without any problems but not from the Robonect Passage web page!
Looking at the tasmota console when pushing the "Passage open" and "Passage close" on the web GUI gives the following:
When "Open Passage" is pressed:
Robonect 1.3 responds: Passage successfully opened at 16:44 clock
Tasmota 9.5.1 console logging:
16:44:49 HTP: Command
16:44:49 SRC: WebCommand from 192.168.1.92
16:44:49 CMD: Group 0, Index 1, Command "BACKLOG", Data "PulseTime1 0"
16:44:49 SRC: Backlog
16:44:49 CMD: Group 0, Index 1, Command "PULSETIME", Data "0"
16:44:49 RSL: RESULT = {"PulseTime1":{"Set":0,"Remaining":0}}
When "Close Passage" is pressed:
Robonect 1.3 responds: Passage successfully closed at 16:48 clock
Tasmota 9.5.1 console logging:
16:48:59 HTP: Command
16:48:59 SRC: WebCommand from 192.168.1.92
16:48:59 CMD: Group 0, Index 1, Command "BACKLOG", Data "PulseTime1 0"
16:48:59 SRC: Backlog
16:48:59 CMD: Group 0, Index 1, Command "PULSETIME", Data "0"
16:48:59 RSL: RESULT = {"PulseTime1":{"Set":0,"Remaining":0}}
As far as I can understand, Robonect is not sending the neccessary "power on" and "power off" command to Tasmota to switch the Relay on and off!
Anyone got any ideas what to do?
Regards Peder
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 706
- Registriert: Di 14. Feb 2017, 17:07
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.1)
- Robonect Firmware: V1.3b
- hat sich bedankt: 8 Male
- wurde gedankt: 82 Male
Re: No poweron cmd to sonoff/tasmota relay
Hello masterohman,
please try the firmware from the download page of the shop. So it should work.
I have not yet tried a current version, so I cannot say whether or how it works.
greeting
Lampi
please try the firmware from the download page of the shop. So it should work.
I have not yet tried a current version, so I cannot say whether or how it works.
greeting
Lampi
Fragen? Fragen!
-
- Forum-Nutzer
- Beiträge: 15
- Registriert: Sa 21. Aug 2021, 18:25
- Mäher: Gardena SILENO City 500
- Robonect Firmware: 1.3
Re: No poweron cmd to sonoff/tasmota relay
Hello Lampi and thanks for your suggestion.
But yes, I have already tried the official Robonect Relay bin file. (and of some reason, I can see on the Console log that Robonect is correctly sending the power on and power off command to the Relay)
The problem with that package is that software package is defining Relay1 on a different GPIO than how my Sonoff board is wired (it is Gpio12 for Relay and Gpio13 for the LED).
Skickat från min Redmi Note 7 via Tapatalk
But yes, I have already tried the official Robonect Relay bin file. (and of some reason, I can see on the Console log that Robonect is correctly sending the power on and power off command to the Relay)
The problem with that package is that software package is defining Relay1 on a different GPIO than how my Sonoff board is wired (it is Gpio12 for Relay and Gpio13 for the LED).
Skickat från min Redmi Note 7 via Tapatalk
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 706
- Registriert: Di 14. Feb 2017, 17:07
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.1)
- Robonect Firmware: V1.3b
- hat sich bedankt: 8 Male
- wurde gedankt: 82 Male
Re: No poweron cmd to sonoff/tasmota relay
Okay, if you use a different model, as it is sold through the Shop (or identical), it will probably not work with the firmware from the Shop.
I had already thought of doing my own experiments with the current firmware, but it will take a while before I get to it. But maybe by then someone will answer who has already implemented something similar.
I had already thought of doing my own experiments with the current firmware, but it will take a while before I get to it. But maybe by then someone will answer who has already implemented something similar.
Fragen? Fragen!
-
- Forum-Nutzer
- Beiträge: 15
- Registriert: Sa 21. Aug 2021, 18:25
- Mäher: Gardena SILENO City 500
- Robonect Firmware: 1.3
Re: No poweron cmd to sonoff/tasmota relay
Yes, I hope that someone from the Robonect team can answer why Robonect 1.3 is not sending the pwrOn and PwrOff cmd to the Tasmota/Sonoff Relay.
- Because as far as I can understand it should work with Tasmota Original software according to the Installation instructions as well as from others in this forum.
Skickat från min Redmi Note 7 via Tapatalk
- Because as far as I can understand it should work with Tasmota Original software according to the Installation instructions as well as from others in this forum.
Skickat från min Redmi Note 7 via Tapatalk
- johan63
- Forum-Nutzer
- Beiträge: 42
- Registriert: Di 7. Jun 2016, 12:18
- Wohnort: Strömsnäsbruk,Sweden
- Mäher: Gardena smart SILENO
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.3 28.06.2021 (Final Release)Kamera
- hat sich bedankt: 2 Male
- wurde gedankt: 1 Mal
- Kontaktdaten:
Re: No poweron cmd to sonoff/tasmota relay
Did you find a solution to this?
Gardena Sileno smart 750. V1.3 28.06.2021 (Final Release)+ Kamera FB: Tommy Cederlund "SWEDEN"
-
- Forum-Anfänger
- Beiträge: 2
- Registriert: Mi 18. Mai 2022, 11:25
- Mäher: Gardena SILENO Life
- Herstellungsjahr: 2020
- Robonect-Modul: Robonect Hx (Rev.6)
- Robonect Firmware: 1.3
Re: No poweron cmd to sonoff/tasmota relay
I wanted to get my Robonect Relay work with Tasmota 12.1.1 as Passage module.
It works with the Relay Firmware from Robonect. But if you use the Tasmota Firmware 6.7.1 (and newer) it does not work.
GPIO 0 is configured as Relay_i 1. It's possible to switch the Relay on or off in web interface or with URL command. But not from the mower and I think I figured OUT why.
I have monitored the traffic from Robonect to tasmota.
The Command which is sent to the Relay e.g. for opening is:
"cm?cmnd=Backlog%20PulseTime1%200;Power1%20On"
And that's the Problem. The semicolon needs to be encoded as %3B as well as the space which is correctly encoded as %20.
That's why the Power command does not appear in the log because it is ignored.
With Tasmota firmware 6.4.1 from Robonect it works without encode. Maybe it was changed in newer TasmotaFirmware so now it need to be encode.
If I am right it has to be adjusted in the Robonec Firmware. Otherwise it is not possible to use the original Tasmota firmware.
BR
Paul
It works with the Relay Firmware from Robonect. But if you use the Tasmota Firmware 6.7.1 (and newer) it does not work.
GPIO 0 is configured as Relay_i 1. It's possible to switch the Relay on or off in web interface or with URL command. But not from the mower and I think I figured OUT why.
I have monitored the traffic from Robonect to tasmota.
The Command which is sent to the Relay e.g. for opening is:
"cm?cmnd=Backlog%20PulseTime1%200;Power1%20On"
And that's the Problem. The semicolon needs to be encoded as %3B as well as the space which is correctly encoded as %20.
That's why the Power command does not appear in the log because it is ignored.
With Tasmota firmware 6.4.1 from Robonect it works without encode. Maybe it was changed in newer TasmotaFirmware so now it need to be encode.
If I am right it has to be adjusted in the Robonec Firmware. Otherwise it is not possible to use the original Tasmota firmware.
BR
Paul
-
- Administrator
- Beiträge: 2907
- Registriert: Di 19. Jan 2016, 18:34
- Wohnort: Kiel
- Mäher: Gardena SILENO City 500
- Firmware des Mähers (MSW): MSW 11.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: stets die Allerneuste :-)
- hat sich bedankt: 1 Mal
- wurde gedankt: 60 Male
- Kontaktdaten:
Re: No poweron cmd to sonoff/tasmota relay
Als Daily-Build nun verfügbar:
https://fw.robonect.de/?latest
https://fw.robonect.de/?latest
Werbefläche zu vermieten. ![Lachend :lol:](./images/smilies/icon_lol.gif)
![Lachend :lol:](./images/smilies/icon_lol.gif)