Hello !
I have bought a used H30x module to my R40li.
I can get to the ZeroConf loader but after loading firmware I cant access the webpage.
I can ping the H30x card so IP connection exists, I have tried dis/connect from WLAN, CRTL+F5 to force a reload but nothing helps.
I have tried the 0.9 and 0.4b firmware, previous owner said the card does not support higher FW then 0.9, dont know if that is correct.
A screenshot from ZeroConf browser exist here: http://themax.se/tmp/h30x.jpg
Would be great to get this up running during this weekend if possible, since its in my cottage and I dont visit it so often.
Brg.
Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Verwendet bitte für aktuelle Mäher bzw. falls ihr die Firmware eures Mähers kürzlich aktualisiert habt, den aktuellen Release-Candidate der Robonect-Firmware: https://fw.robonect.de/?latest Diese wird in ein paar Tagen als offizielle Firmware verfügbar sein. (Stand: 03.04.2024)
No web access after firmware upload [EXPLAINED]
-
- Forum-Anfänger
- Beiträge: 2
- Registriert: Sa 13. Mai 2017, 17:49
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 4.xx.xx
- Herstellungsjahr: 2012
- Robonect-Modul: Robonect Hx (Rev.3)
- Robonect Firmware: 0.9e
No web access after firmware upload [EXPLAINED]
Zuletzt geändert von shadowkiller am Do 30. Apr 2020, 22:37, insgesamt 2-mal geändert.
Grund: correct topic
Grund: correct topic
- SenfmitHonig
- sehr erfahrener Forum-Nutzer
- Beiträge: 457
- Registriert: So 30. Okt 2016, 22:39
- Wohnort: 943xx
- Mäher: Husqvarna Automower 430X
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.2)
- Robonect Firmware: V1.3
- hat sich bedankt: 4 Male
- wurde gedankt: 34 Male
Re: No web access after firmware upload
get the latest firmware!
Install according to instructions
https://forum.robonect.de/viewtopic.php?f=37&t=3142
The latest version should work for you! --> Then you can install the WLan driver.
Install according to instructions
https://forum.robonect.de/viewtopic.php?f=37&t=3142
The latest version should work for you! --> Then you can install the WLan driver.
Bei WLAN-Problemen kann auch der WLAN-Treiber aktualisiert werden. (Vorraussetzung, ZeroConf V1.4 und mindestens Applikation V1.2_RC0 sind zuvor installiert)
-
- Forum-Anfänger
- Beiträge: 2
- Registriert: Sa 13. Mai 2017, 17:49
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 4.xx.xx
- Herstellungsjahr: 2012
- Robonect-Modul: Robonect Hx (Rev.3)
- Robonect Firmware: 0.9e