Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
. Testmöglichkeit für das Daily Build.
Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!
.
.
Robonect relay
-
- Forum-Anfänger
- Beiträge: 4
- Registriert: So 11. Apr 2021, 13:45
- Mäher: Gardena SILENO City 500
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2017
- Robonect-Modul: noch kein Robonect verbaut
- Robonect Firmware: -
- hat sich bedankt: 2 Male
Robonect relay
Can someone tell is it allow to cut wire, and connect robonect Relay in the place mark red X (attack picture). Please answer! BR! Ivo
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 698
- Registriert: Di 14. Feb 2017, 17:07
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.1)
- Robonect Firmware: V1.3b
- hat sich bedankt: 8 Male
- wurde gedankt: 81 Male
Re: Robonect relay
Hello tacko and welcome to the forum.
Why shouldn't it be allowed to cut the cable?
To install the Relay, it must be cut. Otherwise the circuit cannot work.
Greetings
Lampi
Why shouldn't it be allowed to cut the cable?
To install the Relay, it must be cut. Otherwise the circuit cannot work.
Greetings
Lampi
Fragen? Fragen!
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 698
- Registriert: Di 14. Feb 2017, 17:07
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.1)
- Robonect Firmware: V1.3b
- hat sich bedankt: 8 Male
- wurde gedankt: 81 Male
Re: Robonect relay
That depends entirely on how your Passage is structured. If it is like in the picture, it is a possible place. It was already drawn in that way (a few millimeters to the right of your marking). Only the new boundary wire has to be laid without any gap to the previous boundary wire up to the Relay.
- Folgende Benutzer bedankten sich beim Autor Lampi für den Beitrag:
- shadowkiller
- Bewertung: 14.286%
Fragen? Fragen!
-
- Forum-Anfänger
- Beiträge: 4
- Registriert: So 11. Apr 2021, 13:45
- Mäher: Gardena SILENO City 500
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2017
- Robonect-Modul: noch kein Robonect verbaut
- Robonect Firmware: -
- hat sich bedankt: 2 Male
Re: Robonect relay
Hi ! is this OK?
- Dateianhänge
-
- Robonect Relay_Detail Passage.pdf
- (56.34 KiB) 103-mal heruntergeladen
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 698
- Registriert: Di 14. Feb 2017, 17:07
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.1)
- Robonect Firmware: V1.3b
- hat sich bedankt: 8 Male
- wurde gedankt: 81 Male
Re: Robonect relay
I don't quite think so.
I have entered the contact assignment in the picture as it would be correct in my opinion.
The rest looks good.
I have entered the contact assignment in the picture as it would be correct in my opinion.
The rest looks good.
Fragen? Fragen!