Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

Passage module malfunction notification

- alle Auffälligkeiten die es zu klären gilt
- Verdacht, dass ein echter Bug vorliegt

:!: Bevor Du Deinen Bug-Verdacht meldest, wurde er vielleicht schon behoben!

Hast Du das aktuelle Daily Bulid schon ausprobiert? Vielleicht ist Dein Bug ja schon gefixt!? :arrow: Download

Falls das Daily Build Dein Problem nicht lösen konnte, schreibe bitte das Datum aus Deinem installierten Daily Built (schwarze Fußzeile im Robonect-Menü) in Deinen Bug-Bericht dazu! Viel Spaß beim Testen!
Antworten
MarcV
Forum-Nutzer
Beiträge: 10
Registriert: Do 16. Sep 2021, 18:49
Mäher: Husqvarna Automower 305
Robonect Firmware: -

Passage module malfunction notification

Beitrag von MarcV »

Hi,

Today I installed the Multifunktionsrelais.
Everything is working fine, the only problem is that I always get the error mail:

Passage module malfunction!
The Passage could not be opened / closed! Check the connection and settings!


But the Relay open and close as expected.

The notification 'In case of malfunction of the Passage module:' is checked in my notifications settings.

Ofcource, I can uncheck it, but than I don't get a message if it is really failing.

Also to robot is stopped then when 'Abort mowing operation if error occurs' is checked in the Passage settings. So I already unchecked it, otherwise the mower is stopping every time it want to open/close the Passage.

MarcV
Forum-Nutzer
Beiträge: 10
Registriert: Do 16. Sep 2021, 18:49
Mäher: Husqvarna Automower 305
Robonect Firmware: -

Re: Passage module malfunction notification

Beitrag von MarcV »

Hi,

I have to say that this is not happen always. But 3 a 4 times per week.

For the rest, I like Robonect very much :daumenhoch:

Also the pushover and other options are very nice.

Lampi
sehr erfahrener Forum-Nutzer
Beiträge: 698
Registriert: Di 14. Feb 2017, 17:07
Mäher: Husqvarna Automower 330X
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2014
Robonect-Modul: Robonect Hx (Rev.1)
Robonect Firmware: V1.3b
hat sich bedankt: 8 Male
wurde gedankt: 81 Male

Re: Passage module malfunction notification

Beitrag von Lampi »

Hello MarcV,

from your description, I suspect that the reception conditions are not sufficient everywhere in the garden. It could also be related to a change in the AP while sending the command to open or close the gate.

greeting
Lampi
Fragen? Fragen!

MarcV
Forum-Nutzer
Beiträge: 10
Registriert: Do 16. Sep 2021, 18:49
Mäher: Husqvarna Automower 305
Robonect Firmware: -

Re: Passage module malfunction notification

Beitrag von MarcV »

I think I know the problem.

I power the Relay with a solar powerbank. Sometimes I can't reach the Relay also not via IP via the network.
After measuring the voltage on the Relay, I sow that it was not 5V , even when the powerbank was fully charged.
After disconnecting, an reconnection again, it was OK again.
I think the powerbank needs a minimum of current to charge something,

Stefan F.
sehr erfahrener Forum-Nutzer
Beiträge: 159
Registriert: Mo 30. Okt 2017, 07:22
Wohnort: Bergisches Land
Mäher: Gardena SILENO Life SMART
Robonect-Modul: noch kein Robonect verbaut
hat sich bedankt: 1 Mal
wurde gedankt: 7 Male

Re: Passage module malfunction notification

Beitrag von Stefan F. »

Most power banks switch off after a while because the Relay pulls too little.
Gardena Sileno life 750 smart | Robonect SW: V1.3 Release | Robonect: Hx+ Hardware V10

Antworten

Zurück zu „Bug?“