Battery not loading after upgrading to 1.0 preview
-
- Forum-Nutzer
- Beiträge: 32
- Registriert: Di 13. Jun 2017, 18:37
- Wohnort: Sweden
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7
- wurde gedankt: 2 Male
Battery not loading after upgrading to 1.0 preview
Hi all.
As always, I apologize if this has been discussed before...
I upgraded my Robonect to the 1.0 preview today (23.07.2017 version). After that my AM doesn't seem to charge anymore. It's in the charger and says "charging" but the battery percent hasn't gone up. Rather it very slowly goes down. By this rate it will be empty by tomorrow noon, guess that might become a problem. Anyone else recognize the behaviour?
I also like to know, is it safe to downgrade to 0.9e?
/Daniel
As always, I apologize if this has been discussed before...
I upgraded my Robonect to the 1.0 preview today (23.07.2017 version). After that my AM doesn't seem to charge anymore. It's in the charger and says "charging" but the battery percent hasn't gone up. Rather it very slowly goes down. By this rate it will be empty by tomorrow noon, guess that might become a problem. Anyone else recognize the behaviour?
I also like to know, is it safe to downgrade to 0.9e?
/Daniel
- saugbaer
- Forum-Veteran
- Beiträge: 1392
- Registriert: Mo 18. Apr 2016, 01:30
- Wohnort: Ramelsloh
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2022
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.4 beta 08.04.2023 20:42
- hat sich bedankt: 7 Male
- wurde gedankt: 10 Male
Re: Battery not loading after upgrading to 1.0 preview
Cache problem
In the browser, press CTRL + F5
In the browser, press CTRL + F5
Ich bin nicht die Signatur, ich putz hier nur
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
-
- Forum-Nutzer
- Beiträge: 32
- Registriert: Di 13. Jun 2017, 18:37
- Wohnort: Sweden
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7
- wurde gedankt: 2 Male
Re: Battery not loading after upgrading to 1.0 preview
Nope. Had no effect (other than of course the web page reloading). Also I can't understand how an old cache in my browser could make the AM not charge
Anyway, when I upgraded the battery was at 37%. Yesterday when I got to bed it was down to 29% and now it's 21%. That's roughly one percent per hour so I get the feeling if I haven't solved this within 21 hours I have a AM that I can't charge anymore.
I've tried restarting the Robonect. The buttons for shutdown and standby are greyed out (maybe that's normal for 1.0?), otherwise I'd test them. Guess next step will be to turn the AM off with the physical power button and wait a while before turning it on again.
/Daniel
-
- Forum-Nutzer
- Beiträge: 32
- Registriert: Di 13. Jun 2017, 18:37
- Wohnort: Sweden
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7
- wurde gedankt: 2 Male
Re: Battery not loading after upgrading to 1.0 preview
Replying myself here. Tried exactly that and it seems to have sorted the problem out, the percent is now ticking up instead of down.
Should I report the problem somewhere in case it's something Fabian need to solve?
/Daniel
- saugbaer
- Forum-Veteran
- Beiträge: 1392
- Registriert: Mo 18. Apr 2016, 01:30
- Wohnort: Ramelsloh
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2022
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.4 beta 08.04.2023 20:42
- hat sich bedankt: 7 Male
- wurde gedankt: 10 Male
Re: Battery not loading after upgrading to 1.0 preview
Write Fabian a PN
Ich bin nicht die Signatur, ich putz hier nur
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 156
- Registriert: Di 26. Jan 2016, 13:39
- Wohnort: Delmenhorst
- Mäher: Husqvarna Automower 308X
- Firmware des Mähers (MSW): MSW 5.xx.xx
- Herstellungsjahr: 2015
- Robonect-Modul: Robonect H30x (Rev.0)
- Robonect Firmware: V1.0 - Beta7a 15.10.18
Re: Battery not loading after upgrading to 1.0 preview
Hej,Malmgren hat geschrieben: ↑Sa 29. Jul 2017, 22:34 Hi all.
As always, I apologize if this has been discussed before...
I upgraded my Robonect to the 1.0 preview today (23.07.2017 version). After that my AM doesn't seem to charge anymore. It's in the charger and says "charging" but the battery percent hasn't gone up. Rather it very slowly goes down. By this rate it will be empty by tomorrow noon, guess that might become a problem. Anyone else recognize the behaviour?
I also like to know, is it safe to downgrade to 0.9e?
/Daniel
the same problem I had also, after I had installed the FW 1.0 beta for testing. The status was "charging", but the % display was running backwards. Then I reinstalled the FW 0.9e. Since then everything is all right. Perhaps it is only a display error in the FW. But I did not want to risk that the battery "emptied" overnight.
Many greetings to Sweden.
Nachtrag vom 07.08.2017:
Ich habe wohl meinen Fehler gefunden. Ich bin ja der Annahme gewesen, dass das Entladen der Batterie evtl. von der Preview V0.0 käme. Aber nachdem der Husky auch mit der FW 0.9e jetzt am Wochenende keine Ladeaktivität mehr zeigte, habe ich ihn mir mal vorgeknöpft. Die LS gesäubert, alle Anschlusskabel entfernt und gereinigt, die Ladeschalen und -kontakte gesäubert und neu eingestellt, und alles wieder zusammengebaut. Und, er lädt und läuft wieder wie am ersten Tag. Angespornt von diesem Ergebnis, habe ich wieder die FW 0.0 vom 23.07.2017 installiert. Hat sofort auf Anhieb geklappt. Alles läuft bisher ohne Probleme. Die negativen Werte beim Laden sind bisher noch nicht wieder aufgetreten.
Inhaltlich hat sich ja einiges an der neuen FW verändert. Sieht toll aus. Fabian, vielen Dank für deine großartige Arbeit.
---
I have probably found my mistake. I am the assumption that the discharge of the battery possibly from the preview V0.0 came. But after the Husky also with the FW 0.9e now no longer show on weekends, I have him pre-button. The LS cleaned, all connection cables removed and cleaned, the charging baskets and contacts cleaned and re-adjusted, and everything reassembled. And, he loads and runs again as on the first day. Inspired by this result, I have again installed the FW 0.0 from 23.07.2017. It worked immediately. Everything runs so far without problems. The negative values during loading have not yet occurred again.
In terms of content has changed a lot on the new FW. Looks great. Fabian, thank you for your great work.
Zuletzt geändert von Der RTler am Mo 7. Aug 2017, 12:14, insgesamt 1-mal geändert.
---
Bis denne ...
Gruß Werner
Bis denne ...
Gruß Werner
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 208
- Registriert: Di 26. Jul 2016, 16:08
- Wohnort: Schönster Teil Deutschlands
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 2.xx.xx
- Herstellungsjahr: 2011
- Robonect-Modul: Robonect H30x (Rev.0)
- Robonect Firmware: 1.0 beta 5
- hat sich bedankt: 4 Male
Re: Battery not loading after upgrading to 1.0 preview
Hi Malmgren,
I think it is a problem with updating.
At your charging station is only one spring for give electric contact.
So the mover must replace the second spring with logic.
At updating you set the AM in a big fault status(lose communication to the display).
At turn off the AM with the physical power button you make a cold start(reset of AM).
So my tip for updating.
Remove AM from charging station.
Press the stop button on AM.
Make Update.
....
Greeting
ViaHack /Jürgen
I think it is a problem with updating.
At your charging station is only one spring for give electric contact.
So the mover must replace the second spring with logic.
At updating you set the AM in a big fault status(lose communication to the display).
At turn off the AM with the physical power button you make a cold start(reset of AM).
So my tip for updating.
Remove AM from charging station.
Press the stop button on AM.
Make Update.
....
Greeting
ViaHack /Jürgen
Automower: R40Li MSW-Version:2.01.00 MSW-Datum: 2011-09-05 17:32:18 SUB-Version: 2.00.00
Bootloader: V0.4 Kompiliert: 22.10.2016 01:12
W-LAN: AT-Version:V0.51.0 SDK-Version:V1.5.0
Hardware Seriennummer: 05DB0030-39394848-43115243
Bootloader: V0.4 Kompiliert: 22.10.2016 01:12
W-LAN: AT-Version:V0.51.0 SDK-Version:V1.5.0
Hardware Seriennummer: 05DB0030-39394848-43115243
-
- Forum-Nutzer
- Beiträge: 32
- Registriert: Di 13. Jun 2017, 18:37
- Wohnort: Sweden
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7
- wurde gedankt: 2 Male
Re: Battery not loading after upgrading to 1.0 preview
Ah, ok. So maybe it would have been enough just pulling the mower out of the station and putting it back in again?
/Daniel
-
- Forum-Nutzer
- Beiträge: 41
- Registriert: So 2. Apr 2017, 16:39
- Wohnort: Leer (Ostfriesland)
- Mäher: Gardena R38Li
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.3)
- Robonect Firmware: V0.9e
Re: Battery not loading after upgrading to 1.0 preview
Hi!
This is actually a preview.
Errorreports should not be send. If someone has troubble with one of the previews, reinstall the last stable version.
Fabian will tell us, when he want to get bugreports.
Regards, Burkhard
This is actually a preview.
Errorreports should not be send. If someone has troubble with one of the previews, reinstall the last stable version.
Fabian will tell us, when he want to get bugreports.
Regards, Burkhard
Lisa: R38li BJ2016, Main: 6.03.00 Sub: 6.00.00 HMI: 6.05.00 Robonect: Board:V3 2017-02. Firmware 0.9e. Fritzbox 6490 Cable (Kabel Deutschland)
-
- Forum-Nutzer
- Beiträge: 32
- Registriert: Di 13. Jun 2017, 18:37
- Wohnort: Sweden
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7
- wurde gedankt: 2 Male
Re: Battery not loading after upgrading to 1.0 preview
Oh, sorry. Thought he wanted feedback on the preview. Already sent him a mail about this. Guess he'll tell me the same thing then
/Daniel